We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Make an In Ground Basketball Hoop: A Step-by-Step Guide (2026)

Learn how to make an in ground basketball hoop, from choosing a pole and anchoring it in concrete to leveling the backboard and avoiding common mistakes.

Updated November 2026

Learning how to make an in ground basketball hoop means setting a steel pole in a concrete footing, bolting a backboard and rim to a level frame, and letting the concrete cure before play. Most DIY builds come down to four things: a sound hole, a properly sized pole, a plumb and level setup, and patience during the cure. Follow the steps below and you will end up with a hoop that stays put through years of dunks and wind.

Plan the Location and Size Your Hole

Pick a flat spot with at least 10 feet of clearance behind the baseline and room for players to drive. Call 811 before you dig so utility lines can be marked. A common in-ground pole sits in a hole about 24 inches deep and 12 to 18 inches across, though many manufacturers specify depth and diameter for their own pole, so check their instructions first.

Shopping for one? See our guide: 6 Best Spalding Basketball Hoop In-Ground Options Compared (2026).

Set the Pole in Concrete

The pole is what keeps the hoop from wobbling, so the footing matters more than anything else. Follow these steps:

  1. Dig the hole to the depth your pole manufacturer specifies, and add 4 to 6 inches of gravel at the bottom for drainage.
  2. Insert the pole and brace it so it stands plumb in two directions. A torpedo level on two sides works well.
  3. Pour concrete around the base, filling the hole and sloping the top slightly away from the pole so water runs off.
  4. Recheck plumb every few minutes while the mix is still wet, since it can shift.
  5. Let the concrete cure for at least 48 hours before attaching the backboard. Many owners wait a full week for a firmer footing.

Attach the Backboard, Rim and Height Adjustment

Once the footing has cured, assemble the backboard, rim and bracket following the kit’s instructions. Use a tape measure to confirm the rim sits 10 feet above the playing surface, and check that the backboard is level side to side. If your model includes a height-adjustment mechanism, test it before tightening every bolt, because adjusting a fully locked system can strip threads.

Check Alignment and Stability

Before the first game, stand back and sight the rim against the pole. Push firmly on the backboard from several angles. Any movement at the top of the pole usually points to a footing problem or loose hardware. Tighten bolts again after a week, since fasteners often settle during the first few uses.

Common Mistakes

  • Skipping the gravel base, which lets water pool and weaken the footing over time.
  • Pouring concrete before confirming plumb, then trying to correct the pole once the mix sets.
  • Mounting the backboard before the concrete has cured fully.
  • Measuring rim height from a sloped surface instead of the lowest point of the court.
  • Overlooking local permit or setback rules for structures near property lines.
  • A four-foot torpedo level helps you verify plumb on both axes while the concrete sets. View on Amazon
  • A post-hole digger or auger speeds up excavation and gives clean, round walls for the footing. View on Amazon
  • Fast-setting concrete mix saves time on the pour, though standard mix works if you have the labor. View on Amazon

If you want a deeper look at each component, In Ground Basketball Hoop Pole: How to Choose, Set and Anchor One (7 Steps) covers pole selection and anchoring in more detail. For a ready-made option, Lifetime In-ground Basketball Hoop Installation: 7 Steps to a Solid Setup (2026) walks through a typical kit install.

FAQ

How deep should an in-ground basketball hoop pole be set?

Many pole manufacturers call for a hole around 24 inches deep, but the exact depth depends on the pole and backboard size. Always follow the specification in your kit’s manual.

How long does concrete need to cure before playing?

Most concrete reaches workable strength in a few days, but waiting about a week gives a firmer footing. Avoid hanging the backboard or hanging on the rim until the mix has fully set.

Can I build an in-ground hoop without professional help?

Many homeowners handle the digging, pouring and assembly themselves, especially with a two-person crew. If the site has unclear utility lines or soil problems, consult a professional installer or a licensed contractor before digging.

Conclusion

A solid in-ground hoop comes down to a properly dug hole, a plumb pole in cured concrete, and careful leveling of the backboard. Take your time on the footing and check alignment again after the first week. Done right, your hoop will hold up for many seasons of play.

Audrey Hayes

About Audrey Hayes

Audrey Hayes is part of our editorial team and reviews and edits our basketball gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Audrey Hayes
Audrey Hayes

Audrey Hayes writes reviews and buying guides for Hoops Junkie.